Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
Welding current in continuous operation mode at 60% load capacity: max. 250 A for wire welding and 220 A for electrode welding
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, burn back - wire release time at the end of welding.
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Digital display screens allow for accurate parameter monitoring.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-250A
Welding current for electrode welding 10-220 A
Current consumption max 11,6 A (MIG) and 12,1 A (MMA)
Load capacity 60%- 250 A MIG and 60%- 220 A MMA
Arc voltage for MIG welding 16,5- 24 V
Wire feed speed 2- 16 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,93
Efficiency 85%
Protection class IP21
Insulation class F
Dimensions 935x420x720 mm
Weight 48 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 250 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
-
Inverter type wire welding device for both wire welding and electrode welding, as well as TIG welding (LIFT lifting ignition)
Based on IGBT transistors. With single-phase power
Welding current max. 200 A for wire welding, 160 A for electrode welding and 200 A for TIG welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with 0,6mm wire, 0,8mm wire, 1,0mm wire
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Digital display screens allow for accurate parameter monitoring.
Wire feed mechanism with two drive rollers.
Technical specifications
Wire roll 200mm to 5kg
Power supply 1f 230V +-10%
Welding current for MIG welding 50-200A
Welding current for electrode welding 10-160 A
Welding current for TIG welding 10-200 A
Max current consumption 37A
Required mains load protection 25 A C-type
Load capacity 30%- 200 A MIG and 60%- 160 A MMA
Arc voltage for MIG welding 12,3- 26 V
Wire feed speed 2- 12,5 m/min
Weldable wires 0,6-1,0 mm
Wire feed mechanism with two drive wheels
Power factor 0,76
Efficiency 85%
Protection class IP21S
Insulation class H
Dimensions 470x190x300 mm
Weight 9 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
With a color LCD screen
Welding current in continuous operation mode at 60% load capacity: max. 300 A for wire welding and 250 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with CO2 gas, steel with mixed gas, welding with filler wire. When a program is selected, the LED next to the corresponding program flashes
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
The large LCD screen allows you to monitor the exact parameters for example.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-300A
Welding current for electrode welding 10-250 A
Welding current for TIG welding 10-300 A
Max current consumption 17 A
Load capacity 60%- 300 A MIG and 60%- 250 A MMA
Arc voltage for MIG welding 16,5- 29 V
Wire feed speed 2- 18 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,85
Efficiency 85%
Protection class IP21S
Insulation class F
Dimensions 920x470x740 mm
Weight 38 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 360 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
With a color LCD screen
Welding current in continuous operation mode at 60% load capacity: max. 250 A for wire welding and 220 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with CO2 gas, steel with mixed gas, welding with filler wire. When a program is selected, the LED next to the corresponding program flashes
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
The large LCD screen allows you to monitor the exact parameters for example.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-250A
Welding current for electrode welding 10-220 A
Welding current for TIG welding 10-250 A
Max current consumption 12 A
Load capacity 60%- 250-A MIG and 60%- 220 A MMA
Arc voltage for MIG welding 16,5- 26,5 V
Wire feed speed 2- 18 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,85
Efficiency 85%
Protection class IP21S
Insulation class F
Dimensions 920x470x740 mm
Weight 39 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 240 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type wire welding device for both wire welding and electrode welding, as well as TIG welding (LIFT lifting ignition)
With single-phase power
Welding current max. 200 A for wire welding, 160 A for electrode welding and 160 A for TIG welding
The device is equipped with simple synergic control for MIG/MAG welding, allowing to set parameters manually.
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance,
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Digital display screens allow for accurate parameter monitoring.
Wire feed mechanism with two drive rollers.
Technical specifications
Wire roll 200mm to 5kg
Power supply 1f 230V +-10%
Welding current for MIG welding 20-200A
Welding current for electrode welding 20-160 A
Welding current for TIG welding 20-160 A
Current consumption max MIG 26,4 A, MMA 23,2 A, TIG 14,4 A
Required mains load protection 25 A C-type
Load capacity 60%- 200 A MIG, 60%- 160 A MMA and TIG
Arc voltage for MIG welding 16- 24 V
Wire feed speed 3- 18 m/min
Weldable wires 0,6-1,0 mm
Wire feed mechanism with two drive wheels
Power factor 0,93
Efficiency 85%
Protection class IP21S
Insulation class F
Dimensions 400x195x270 mm
Weight 10 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
SPARTUS® EasyMIG 125 is a light, compact wire welding machine based on IGBT transistors, with a single-phase 230V supply. Enables welding with gasless filler wire. Maximum welding current 100 A. Equipped with protection functions with intelligent overvoltage, overcurrent and overheating protections. If any of these problems occur, an alarm light will illuminate on the control panel and the welding current output circuit of the device will be automatically shut down to protect and extend the life of the device. SPARTUS® EasyMIG 125 is suitable for working outdoors and on construction sites thanks to its small dimensions and weight. The wire feed mechanism is equipped with two drive rollers and a 1kg/100mm wire roll holder. The MIG welding torch and ground cable are permanently connected to the machine. Technical data: Power supply ~1× 230V ± 10% 50 / 60 Hz Welding current 40 - 100 A Load capacity 30% 100 A Arc voltage 16.6 V Wire feed mechanism, with 2 drive rollers Wire roll 1 kg / Ø100 mm Wire diameter 0.8 mm Current consumption up to 19.6 A Power factor (cos?) 0.58 Insulation class F Protection class IP21S Weight 5.8 kg Dimensions 410×285×150 mm Complete set: • EasyMIG 125 • MIG torch SPE 150 3m • Earthing cable with terminal -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
With a color LCD screen
Welding current in continuous operation mode at 60% load capacity: max. 350 A for wire welding and 300 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with CO2 gas, steel with mixed gas, welding with filler wire. When a program is selected, the LED next to the corresponding program flashes
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
The large LCD screen allows you to monitor the exact parameters for example.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-350A
Welding current for electrode welding 10-300 A
Welding current for TIG welding 10-350 A
Max current consumption 21 A
Load capacity 60%- 350 A MIG and 60%- 300 A MMA
Arc voltage for MIG welding 9,9- 35 V
Wire feed speed 0,8- 16 m/min
Weldable wires 0,8-1,6 mm
Wire feed mechanism with four drive wheels
Power factor 0,93
Efficiency 80%
Protection class IP21S
Insulation class H
Dimensions 920x480x735 mm
Weight 37 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 360 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type wire welding device for both wire welding and electrode welding, as well as TIG welding (LIFT lifting ignition)
Based on IGBT transistors. With single-phase power
Welding current max. 200 A for wire welding, 180 A for electrode welding and 200 A for TIG welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with 0,6mm wire, 0,8mm wire, 1,0mm wire and Aluminum with 1,0mm wire.
When welding steel, you can choose shielding gas CO2 or mixed gas, there is also a separate program for welding with filler wire. A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Various parameters can be set easily and quickly on the digital screen. When the programs are in place, the screen will graphically display the shape of the weld suggesting the thickness of the material at the given current.
Wire feed mechanism with two drive rollers.
Technical specifications
Wire roll 200mm to 5kg
Power supply 1f 230V +-10%
Welding current for MIG welding 50-200A
Welding current for electrode welding 10-180 A
Welding current for TIG welding 10-200 A
Max current consumption 40A
Required mains load protection 25 A C-type
Load capacity 60%- 200 A MIG, 60%- 200 A TIG and 60%- 180 A MMA
Arc voltage for MIG welding 12,3- 26 V
Wire feed speed 2- 12,8 m/min
Weldable wires 0,6-1,0 mm
Wire feed mechanism with two drive wheels
Power factor 0,76
Efficiency 85%
Protection class IP21S
Insulation class H
Dimensions 490x230x330 mm
Weight 12 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable.
-
Spartus ProMIG 335 DP- Dual Pulse Synergy is a multifunctional inverter welding device,
with which wire welding, electrode welding and TIG welding can be performed.
MIG/MAG welding modes: synergic with double pulse, synergic with pulse, synergic without pulse, with manual setting. A machine suitable for use in industrial production with a high load capacity, with a load capacity of 300% at the maximum welding current of 60A. With three-phase 400 V power supply. Wire feed mechanism with four drive rollers. A compact device with a built-in liquid cooling system, mounted on a base cart. Modern technological solutions have been used in the design of the device. Materials to be welded in the MIG/MAG mode: steel, stainless steel, acid-resistant steels and aluminum alloys.
Allows you to choose the wire type and diameter Special emphasis has been placed on aluminum welding when creating programs and setting options.
Key Features:
1P Pulse- MIG/MAG welding with a pulse, which greatly simplifies spatter-free welding with a spray arc
2P Pulse (Dual Pulse) - MIG/MAG welding with a double pulse, especially suitable for aluminum welding, allows to achieve an approximate result that can be obtained with TIG welding
2T/4T welding modes
Spot welding with a timer
A simple and easy-to-set control panel enables precise control of all welding parameters.
In the manual mode, it is possible to adjust the arc voltage, the speed of the wire feed and the inductance for wire welding.
In the case of synergic control, the welding parameters are set according to the input data.
In the pulse mode, it is possible to set the pulse delta value, pulse frequency, pulse duration and base current.
The wire feed mechanism is equipped with four drive rollers, so a long welding torch can be used for welding.
A 5m torch is included in the set of the device. Despite the compactness and small dimensions, both 5 kg D200 and 15 kg D300 wire rolls can be used.
TIG welding can be performed with lift ignition and 2T/4T switching, current drop and aftergas duration can be set.
Arc force arc dynamics and Hot start e are helpful for MME welding with a melting electrode. simplified arc ignition.
Technical specifications:
Power supply 3 phases 400 V +-10% 50 Hz
Welding current 10- 300 A
Load capacity 60% 300 A
Welding arc voltage 14,5- 29 V
Wire feed mechanism with 4 drive rollers
Wire feed speed 2- 24 m/min
Wire diameter 0,8-1,2 mm
SPOT welding time timer
Wave control - inductance setting
Welding modes 2T/4T/s4T
Smooth wire acceleration when starting welding
Burn-back at the end of the welding arc
Pre- and post-gas
Spoolgun readiness
Welding current for TIG welding 10-300 A
Ignition of the arc during TIG welding with Lift
TIG current drop at the end of welding 0-10
Welding current when welding coated fusible electrodes 10-300 A
Arc force- adjusting the intensity of the welding arc MMA
Hot start - simplified arc ignition MMA
Current consumption MIG 14,8 A, MMA 16,3 A, TIG 11,5 A
Power factor cos phi 0,9
Insulation class H
Protection class IP21S
Weight 58,5 kg
Dimensions 930x490x930 mm
Complete set:
Welding device Spartus ProMIG 335 DP
Wire feed mechanism with 4 drive wheels
Water cooling system
Coolant Hypercoolant
Truck with 4 wheels
MIG torch Spartus SPP241 5m
Electrode holder with 3 m cable
Earth terminal with 3 m cable
Gas hose between the machine and the cylinder -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
Welding current in continuous operation mode at 60% load capacity: max. 300 A for wire welding and 250 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with CO2 gas, steel with mixed gas, welding with filler wire. When a program is selected, the LED next to the corresponding program flashes
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Digital display screens allow for accurate parameter monitoring.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-300A
Welding current for electrode welding 10-250 A
Welding current for TIG welding 10-300 A
Max current consumption 17 A
Load capacity 60%- 300 A MIG and 60%- 250 A MMA
Arc voltage for MIG welding 16,5- 29 V
Wire feed speed 2- 18 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,85
Efficiency 85%
Protection class IP21S
Insulation class F
Dimensions 920x420x740 mm
Weight 38 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 360 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type wire welding device for both wire welding and electrode welding, as well as TIG welding (LIFT lifting ignition)
Based on IGBT transistors. With single-phase power
Welding current max. 220 A for wire welding, 200 A for electrode welding and 220 A for TIG welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with 0,6mm wire, 0,8mm wire, 1,0mm wire and Aluminum with 1,0mm wire.
When welding steel, you can choose shielding gas CO2 or mixed gas, there is also a separate program for welding with filler wire. A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Various parameters can be set easily and quickly on the digital screen. When the programs are in place, the screen will graphically display the shape of the weld suggesting the thickness of the material at the given current.
Wire feed mechanism with two drive rollers.
Technical specifications
Wire roll 200mm 5kg or 300mm 15kg
Power supply 1f 230V +-10%
Welding current for MIG welding 50-220A
Welding current for electrode welding 10-200 A
Welding current for TIG welding 10-220 A
Current consumption max. MIG 37A, TIG 28A, MMA 39A
Required mains load protection 25 A C-type
Load capacity 60%- 220 A MIG, 60%- 220 A TIG and 60% 200A MMA
Arc voltage for MIG welding 16,5- 25 V
Wire feed speed 2- 12,5 m/min
Weldable wires 0,6-1,0 mm
Wire feed mechanism with two drive rollers
Power factor 0,76
Efficiency 85%
Protection class IP21S
Insulation class H
Dimensions 570x265x460 mm
Weight 19 kg
Included
Earth terminal with cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with cable.
MIG torch consumables box -
Description
Modern multifunctional two-in-one industrial professional welding device.
Allows welding with MIG/MAG and MMA methods.
The device is manufactured using inverter technology and the highest quality components are used.
The welding current used in MIG/MAG welding max. 420 A and also up to 420 A for electrode welding.
With three-phase 400 V power supply.
With a separate wire feed mechanism, the top-class 4-drive roller wire feed mechanism ensures stable and uniform wire movement even with a long torch, regardless of the type of wire.
The wire feed mechanism is equipped with a comfortable handle and base wheels to move it away from the machine if necessary.
Intuitive control panel allows smooth and precise parameter adjustment: arc voltage, wire feed speed, inductance control
(for MIG/MAG) and welding current (for MMA electrode welding).
At the bottom of the machine, there is a separate openable storage compartment for storing the welding torch, accessories or other necessary items.
The device is equipped with digital displays, and the values of the parameters to be set are displayed on the screens.
Spartus Pro MIG series machines are designed for use in industry and are able to successfully withstand heavy loads under the most difficult working conditions.
Excellent output parameters, load capacity indicators, effective cooling system, durable housing, 2T/4T modes
Technical specifications:
Power supply 3 phases 400 V +-10% 50/60 Hz
Welding current MIG 80- 420 A
Load capacity 60% 420 A
Arc voltage MIG 18-35 V
Wire feed speed 2,5- 21,0 m/min
Wire feed mechanism with 4 drive rollers
Wire spool 200/ 300 mm, 15 kg
Wire diameters 0,8-1,6 mm
2T/4T control
Inductance control
Welding current for MMA electrode welding 30-420 A
Load capacity MMA 60% 420 A
Max current consumption 30,7 A
Power factor cos 0,85
Efficiency 85%
Insulation class F
Protection class IP23
Weight 99 kg
Dimensions 1060x420x1400 mm
Completeness
3m electrode holder
3m grounding cable
Package of intermediate cables between the machine and the wire feed mechanism, 5m
Gas hose with clamps
Gas reducer with two manometers
MIG torch Spartus Pro 360 5m
Wire rollers for 1,0-1,2 mm wire -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
Welding current in continuous operation mode at 60% load capacity: max. 300 A for wire welding and 250 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available synergistic programs for steel 0,8/1,0/1,2 mm wires.
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
The large digital screen allows you to monitor the exact parameters for example.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-300A
Welding current for electrode welding 10-250 A
Welding current for TIG welding 10-300 A
Current consumption max MIG 17 A; TIG 14 A; MMA 13 A
Load capacity 60%- 300 A MIG and TIG; 60%- 250 A MMA
Arc voltage for MIG welding 16,5- 29 V
Wire feed speed 2- 12,5 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,93
Efficiency 85%
Protection class IP21S
Insulation class H
Dimensions 570x265x460 mm
Weight 19 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 360 3m
Gas hose with hose clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type modern wire welding device, designed for professional use on a daily basis.
Allows you to weld with conventional wire in both MIG and MAG mode, as well as with gasless filler wire, as it allows you to change the polarity of the welding current.
You can also weld with fusible electrodes (MMA) and TIG lift method. The built-in gas valve and control plug allow the use of a push-button torch for TIG welding.
In addition to IGBT power transistors, MCU controller, PWM technology and PFC filters are used in the internal construction of the device, which together ensure a stable and high-quality welding current.
The device is equipped with the following welding support functions:
Synergic control - 16 built-in welding programs
Wave control - precise adjustment of the dynamics of the welding arc ensures complete control of the welding arc, allows to reduce welding spatter and can adjust the width and penetration of the arc.
Burn back - accurate welding wire speed control reduces the risk of the wire sticking to the wire nozzle, is helpful in finishing welding.
Slow feed- a smooth increase in the speed of the wire at the start of welding. Especially recommended for welding with higher welding currents and/or wire feed speeds.
A smooth wire feed at the start of welding reduces the risk of defects at the start of welding.
2T/4T- 2-stroke and 4-stroke mode
Spool Gun- readiness for welding with a Spool Gun torch. Available as a separate accessory.
Regimes supporting TIG welding: 2T/4T, welding current drop adjustment 0-10s, tail gas adjustment
Modes supporting MMA electrode welding: Hot Start, Arc Force, VRD - low idle voltage in standby mode
The device has been specially designed following the advice and wishes of shipbuilding welders and has been enlarged
resistance to moisture, salty environment and corrosion - so it is well suited for use in metal industries, where there are often difficult environmental conditions.
It is also suitable for those performing repair and maintenance work when working in an outdoor environment.
The maximum welding current in MIG/MAG, MMA and TIG modes is up to 200A.
Wire roll 200mm to 5kg
Wire feed mechanism with two drive rollers
The device is equipped with a large graphic display for monitoring and setting parameters
Technical specifications
Power supply 1f 230V +-10%
Welding current for MIG welding 25-200 A
Welding current for TIG welding 10-200 A
Welding current for electrode welding 10-200 A
Max current consumption 32 A
Load capacity 40% 200 A
Arc voltage for MIG welding 15,3- 24 V
Wire feed speed 2,5- 16,5 m/min
Weldable wires 0,6-1,0 mm
VRD idle voltage 14 V
Power factor 0,99
Efficiency 85%
Insulation class H
Protection class IP23
Dimensions 530x215x410 mm
Weight 17 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Introductory video:
https://www.youtube.com/watch?v=oUc8iX-FqCA -
Description The device can weld carbon steel, stainless steel, various aluminum alloys, etc. Welding current max. 200A, smooth adjustment without steps. Both remote control and pedal control are available as accessories. When connecting a remote control or pedal, the device automatically recognizes the equipment being used and automatically switches to control from the remote control. The device is suitable for all TIG welding applications with full parameter settings. It is also suitable for welding all electrodes used in electrode welding. Suitable applications for welding tanks, pipelines, boilers, industrial applications and maintenance work. Main features: Arc stability and arc control, in electrode welding, automatic sensitivity adjustment when the distance between the material and the electrode tip changes. Automatic synergistic control for AC parameters (balance-frequency-compensation), simplified, optimal and easy setting. Simple setting and saving of parameters with one button. Double automatic cooling, the fan is activated only when necessary. The tunnel-type cooling system ensures the protection of electronic components from particles coming with the air flow. Air currents move inside the machine only to the components that need cooling. STAND-BY function, the device switches to standby mode if not used for 10 minutes. This ensures a longer life of the electronic components of the device and increases the efficiency of the device. Minimal electricity consumption thanks to excellent energy efficiency. The electronics of the device are built in such a way that the energy from the power supply is used as efficiently as possible. Anti-stick protection, arc dynamics, simplified arc ignition, LIFT lifting and HF non-contact ignition for TIG welding. Built-in supply voltage stabilizer, the device can also be used with generator power and with large supply voltage fluctuations. The device is equipped with VRD voltage reduction device function e. When idling, the voltage drops to a very low level, ensuring safety even when working in very extreme conditions (damp, wet). Technical data Power supply 1 phase 230 V Protection 25 A Power consumption 9,5 kVA Permitted supply voltage 180- 280 V Welding current 10- 200 A Load capacity for electrode welding according to EN60974-1 40 oC 160 A 60%, 130 A 100% Load capacity for TIG welding according to EN60974- 1 40 oC 170 A 60%, 140 A 100% Pulse frequency up to 500 Hz No-load voltage 65 V Protection class IP23 Weight 14 kg Dimensions 465x280x360 mm Complete set Earth terminal with 2m cable TIG torch 4m gas hose -
Compact and simple inverter welding device based on IGBT transistors. Enables welding both fusible electrodes (MMA) and TIG Lift DC in case of using the separately available TIG torch with article code SH4431. Welding current adjustable between 10-160A, the machine has enough power to weld 4mm electrodes as well. Equipped with an electronic current indicator, adjustment using one large button. The device is also equipped with a VRD (Voltage Reduction Device) function, which makes the device safe to use even in wet conditions. TECHNICAL DATA: Voltage:~1 × 230V ± 10% 50 / 60 Hz Welding current [A] 10 – 160 Load capacity 40% 160A No-load voltage 82V Max current 32 A Required fuse 25 A Type C Power factor (cos?) 0,76 Efficiency [%] 85 Insulation class H Protection class IP21s Weight 4 kg Dimensions 270x130x200mm Complete set: Carrying case Electrode holder with 2m cable Grounding terminal with 1,5m cable Protective shield Slag hammer Wire rod -
Compact inverter welding device based on IGBT transistors. Enables welding both fusible electrodes (MMA) and TIG Lift DC in case of using the separately available TIG torch with article code SH4431. The welding current is adjustable between 10-200A, the machine has enough power to weld even 4mm electrodes. The intuitive LCD screen immediately gives recommendations according to the selected welding current, which diameter electrode to use and which material thickness to weld with this current. The device is also equipped with a VRD (Voltage Reduction Device) function, which makes the device safe to use even in wet conditions. TECHNICAL DATA: Voltage:~1 × 230V ± 10% 50 / 60 Hz Welding current [A] 10 – 200 Load capacity 60% 200A, 100% 140A No-load voltage 80V Max current 42 A Required protection 25 A C-type Power factor (cos?) 0,76 ... -
The set includes: -Inverter welding COTT195 High performance and low weight, compact machine. Case with double walls. The device can also be used with an extension cord and when working from a generator. Technical data: Power supply 1 f 230 V Permitted supply voltage 140-280 V Power consumption 6,4 kW, 8 kVA Protection 16 A Welding current 10-180 A Load capacity for MMA electrode welding according to EN60974-1 40 oC 180 A 35%, 110 A 60%, 85 A 100% Load capacity during TIG lift welding according to EN60974-1 40 oC 180 A 40%, 130 A 60%, 100 A 100% Number of electrodes to be welded 1,6- 2,5 mm continuously, 3,2 mm 40 pcs/h, 4,0 ,12 mm 95 pcs/h No-load voltage 23 V Protection class IP315 Dimensions 135x285x4 mm Weight 850 kg Complete set: carrying case, shoulder strap, ground terminal with cable, electrode holder with cable. - The Sacit P2 self-darkening welding mask is equipped with 2032 photo sensors and a solar battery, as well as a replaceable auxiliary power battery CR90. True color - a filter element with real colors that ensures a clean and clear view and less eye strain. Welding and grinding function. Element dimensions 110x485 mm Weight 96 g Viewing aperture 39x9 mm Adjustable darkness 13-16 DIN UV/IR protection 0,3 DIN Response speed 0,1 ms Switching from dark to light 1-1 s Optical class 1/1/2/6013 - INE SUPER 2,5 300x2,5mm 46.00kg Rutile-coated electrode characterized by rapid arc ignition, good-looking weld pool and easy slag removal. Suitable for welding small and medium-sized unalloyed (carbon) steel building structures. Designed for use in all welding positions - including the vertical top down position. Similar brands from other manufacturers: Esab OK45, Elga P6013S, Hyundai S-XNUMX.LF -
Compact inverter welding device based on IGBT transistors. Enables welding fusible electrodes (MMA) With three-phase 400 V power supply. Welding current adjustable between 20-250A, the machine has enough power to weld 5 mm electrodes as well. Ensures a strong, focused and stable welding arc. The easy-to-use control panel is equipped with a digital display. TECHNICAL DATA: Voltage:~3 × 400V ± 10% 50 / 60 Hz Welding current [A] 20 – 250 Load capacity 60% 250A No-load voltage 69V Max current 15 A Required protection 16 A C-type Power factor (cos?) 0,93 Efficiency [ %] 80 Insulation class H Protection class IP21S Weight 11,5 kg Dimensions 500x225x340mm Complete set: Carrying case Electrode holder with cable Ground terminal with cable -
A compact inverter welding device with excellent technical characteristics. Low current consumption, it is also possible to operate from a generator with a nominal power of at least 5,3 kW 1 phase. Allowed supply voltage fluctuation in the range of 180-280 V. It is also possible to perform TIG welding with direct current using the lifting method (LIFT). With double cooling.
Number of welding electrodes 1,6-3,2mm continuous, 4,0mm 20pcs/h
Technical specifications:
Power supply 1 phase 230 V
Protection min. 16 A
Power 6,6 kVA/5,28 kW
Allowed supply voltage 180-280 V
Welding current 10- 180 A
Current max. welding current 180 A
Load capacity for electrode welding according to EN60974-1 at 40 oC 160A 45%, 140A 60%, 100A 100% Load capacity for TIG welding according to EN60974-1 at 40 oC 180A 50%, 150A 60%, 110A 100%
No-load voltage 80 V
Protection class IP23S
Weight 4,5 kg
Dimensions 305x115x225 mm
Completeness
Carrying case
Earth terminal with 2 m cable
Electrode holder with 3 m cable
Shoulder strap
-
Features:
High performance and low weight, compact machine
Case with double wall
Can also be used with an extension cord and when running on generator power
Technical specifications:
Power supply 1 f 230 V
Allowed supply voltage 140-280 V
Power consumption 6,4kW, 8 kVA
Protection 16 A
Welding current 10-180 A
Load capacity for MMA electrode welding according to EN60974-1 40 oC 180 A 35%, 110 A 60%, 85 A 100%
Load capacity during TIG lift welding according to EN60974-1 40 oC 180 A 40%, 130 A 60%, 100 A 100%
Number of welding electrodes 1,6-2,5 mm continuously, 3,2 mm 40 pcs/h, 4,0 mm 12 pcs/h
No-load voltage 95 V
Protection class IP23
Dimensions 315x135x285 mm
Weight 4 kg
Complete set:
Carrying case
Shoulder strap
Earth terminal with cable
Electrode holder with cable -
Energy consumption 1,8kW / 60% Load at room temperature 20C 60 Load according to standard 60974-1-40-c 10 Supply current 230V Welding current 160 A Idle voltage 70V Electrode diameter 1.6-3.24 mm Weight 4.1 kg