A built-in thermometer measures the actual temperature in the watch area; 36 melodies; Clock and key with LED lighting; Place of name tag; Clock button moisture class IP44, door bell IP20; volume control - 3 steps (60-87 dB); Fixing the button with self-adhesive tape or fixing holes; Night light function; Color: white; Transmission frequency: 433 MHz; Signal range in open space: 120 m; Choose the location of the clock button so that the working area is free of obstacles in relation to the receiver, otherwise the working area of ​​the equipment will be reduced. The melody selection is automatically saved after playback ends. Select the volume using the two-step switch on the receiver panel. The learning function allows you to pair door bells and buttons with one set. In this way, several bell buttons can be used to operate one door bell or vice versa. If you need to assign a new/different transmitter to the receiver, do the following: 1. Press the melody selection button for 3 seconds until you hear a double beep. 2. At the same time, press and hold the button of the watch button you want to deploy. It assigns the sender to the receiver. The original transmitter is also assigned (Figure 1). In the same way, you assign a new receiver, or door bell, to the transmitter, or bell button. All previous included receivers are also assigned to the transmitter (Figure 2). 4 transmitters can be paired with one receiver (Figure 1). Disconnecting the bell button from the doorbell 1. Unplug the doorbell for five seconds. 2. Then plug the doorbell back into the mains and press and hold the volume button for three seconds. 3. At the same time, press the button of the clock button that you do not want to delete, ie. that you continue to use. Power supply: button: 1x 12V (LR23A) battery (included in the set); at: AC 230V - socket. Operating temperature: -15 ° C to + 65 ° C; Power consumption: receiver (clock) in standby mode: <0,5W; Transmitter (button) in operating mode: <10 mW.

58 different melodies on the wireless doorbell Volume adjustment - 5 levels (25-85dB) 4 modes - ringing, flashing light, ringing + flashing light, ringing + steadily lit light. LED indicator on both the clock and the clock button Place of the covered name tag on the clock button Protection class IP55 for the clock button, IP20 for the clock. Fixing the bell button and doorbell with self-adhesive tape or with mounting holes Color - white Signal range in open space: 250 m Transmission frequency: 433 MHz Power supply: bell button: 1x 3V (CR2032) battery (included in the set) doorbell: 230V Operating temperature: -10 ° C to + 40 ° C It is possible to pair 6 bell buttons with one door bell and vice versa. Open the battery compartment cover of the new transmitter and remove the insulating tape from the 3V CR2032 batteries. Observe the polarity of the batteries! Choose the location of the clock button so that the working area is free of obstacles in relation to the receiver, otherwise the working area of ​​the equipment will be reduced. The clock face is weatherproof, but still choose an area protected from precipitation and direct sunlight. Use the melody button to select and change the melody. The melody selection is saved automatically when the melody ends. Adjust the volume from the volume button. Press the multifunction button to select the ringtone mode. The learning function allows you to pair door bells and buttons with one set. In this way, several bell buttons can be used to operate one door bell or vice versa. Press the multifunction button on the doorbell to set new transmitters. Then press the bell button 30 times within 2 seconds until the buzzer starts. To delete the transmitter from the doorbell memory, hold down the multifunction button for 10 seconds.

Wireless doorbell with mains power, bell button with battery power. Working radius 100 meters; 48 melodies, adjustable volume; frequency 433,92 MHz. Included: 23A battery operated clock button (IP44). 1x23A battery; receiver (IP20, 220V). Color: white.