Spartus ProMIG 500 Dual Pulse Synergy is a multifunctional inverter welding device,

with which wire welding, electrode welding and TIG welding can be performed.

Modern technological solutions are used in the design of the device, such as:

IGBT transistors, PWM (pulse with modulation), MCU (multipoint control unit).

With three-phase power and allows welding in continuous mode with a welding current of up to 500 A.

Materials to be welded in the MIG/MAG mode: steel, stainless steel, acid-resistant steels and aluminum alloys.

Special emphasis has been placed on aluminum welding when creating programs and setting options.

Key Features:

1P Pulse- MIG/MAG welding with a pulse, which greatly simplifies spatter-free welding with a spray arc

2P Pulse (Dual Pulse) - MIG/MAG welding with a double pulse, especially suitable for aluminum welding, allows to achieve an approximate result that can be obtained with TIG welding

2T/4T welding modes

Spot welding with a timer

A simple and easy-to-set control panel enables precise control of all welding parameters.

In the manual mode, it is possible to adjust the arc voltage, the speed of the wire feed and the inductance for wire welding.

In the case of synergic control, the welding parameters are set according to the input data.

The wire feed mechanism is equipped with four drive rollers, so a long welding torch can be used for welding.

A 5m torch is included in the set of the device. Despite the compactness and small dimensions, both 5 kg D200 and 15 kg D300 wire rolls can be used.


Technical specifications:

Power supply 3 phases 400 V +-10% 50 Hz

Welding current 15- 500 A

Load capacity 60% 500 A, 100% 400 A

Welding arc voltage 14,8- 39 V

Wire feed mechanism with 4 drive rollers

Wire feed speed 1,5- 24 m/min

Wire diameter 0,8-1,6 mm

Built-in welding programs- 1P pulse- 23pcs, 2P dual pulse- 23pcs, Synergy- 20pcs

dPC pulsation delta 30- 70 %

FdP Pulse frequency 2P 0,5- 3,0 Hz

dut double pulse width 10- 90 %

bAL welding arc height -10- +10

SPOT welding time timer

Wave control - inductance setting

Welding modes 2T/4T/s4T

SCP initial current 1- 200 %

SAL Initial current welding arc length -10- +10

ECP final current 1- 200 %

EAL final current welding arc length -10- +10

Smooth wire acceleration when starting welding

Burn-back at the end of the welding arc

Pre- and post-gas

Spoolgun readiness

Welding current for TIG welding 10-500 A

Ignition of the arc during TIG welding with Lift

TIG current drop at the end of welding 0-10

Welding current when welding coated fusible electrodes 10-500 A

Arc force- adjusting the intensity of the welding arc MMA

Hot start - simplified arc ignition MMA

VRD- low open-circuit voltage when the device is in standby mode

Current consumption MIG 45 A, MAG 47 A, TIG 37 A

Power factor cos phi 0,7

Efficiency 85 %

Insulation class H

Protection class IP23

Weight 102 kg

Dimensions 1100x500x1500 mm


Complete set:

Welding device Spartus ProMIG 500 Dual Pulse Synergy

Wire feed mechanism with 4 drive wheels

Water cooling system

Truck with 4 wheels

Intermediate cable between the power part of the machine and the wire feed mechanism, 5m

MIG torch Spartus SPP501LCD 5m

Electrode holder with 3 m cable

Earth terminal with 3 m cable