Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
Welding current in continuous operation mode at 60% load capacity: max. 250 A for wire welding and 220 A for electrode welding
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, burn back - wire release time at the end of welding.
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Digital display screens allow for accurate parameter monitoring.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-250A
Welding current for electrode welding 10-220 A
Current consumption max 11,6 A (MIG) and 12,1 A (MMA)
Load capacity 60%- 250 A MIG and 60%- 220 A MMA
Arc voltage for MIG welding 16,5- 24 V
Wire feed speed 2- 16 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,93
Efficiency 85%
Protection class IP21
Insulation class F
Dimensions 935x420x720 mm
Weight 48 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 250 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
-
Ühefaasilise 230V toitega traadikeevitusseade gaasita täidistraadiga keevitamiseks. Varustatud termokaitsega, komplektis maanduskaabel ja keevituspõleti. https://youtu.be/FNwxYoLWV7g Tehnilised näitajad Toide 1faas 230V Tarbitav võimsus max 3,6 kVA Tarbitav võimsus 60% koormatavusel 1,5 kVA Kaitse 13 A Võimsusfaktor 0,9 Tühijooksupinge 37 V Keevitusvool 50- 120A Koormatavus 105A 15% Voolutugevuse astmeid 4 Keevitustraat 0,8-0,9mm Isolatsiooniklass H Kaitseklass IP21 Mõõdud 450x240x400mm Kaal 18,5kg -
Inverter type wire welding device for both wire welding and electrode welding, as well as TIG welding (LIFT lifting ignition)
Based on IGBT transistors. With single-phase power
Welding current max. 200 A for wire welding, 160 A for electrode welding and 200 A for TIG welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with 0,6mm wire, 0,8mm wire, 1,0mm wire
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Digital display screens allow for accurate parameter monitoring.
Wire feed mechanism with two drive rollers.
Technical specifications
Wire roll 200mm to 5kg
Power supply 1f 230V +-10%
Welding current for MIG welding 50-200A
Welding current for electrode welding 10-160 A
Welding current for TIG welding 10-200 A
Max current consumption 37A
Required mains load protection 25 A C-type
Load capacity 30%- 200 A MIG and 60%- 160 A MMA
Arc voltage for MIG welding 12,3- 26 V
Wire feed speed 2- 12,5 m/min
Weldable wires 0,6-1,0 mm
Wire feed mechanism with two drive wheels
Power factor 0,76
Efficiency 85%
Protection class IP21S
Insulation class H
Dimensions 470x190x300 mm
Weight 9 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
With a color LCD screen
Welding current in continuous operation mode at 60% load capacity: max. 300 A for wire welding and 250 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with CO2 gas, steel with mixed gas, welding with filler wire. When a program is selected, the LED next to the corresponding program flashes
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
The large LCD screen allows you to monitor the exact parameters for example.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-300A
Welding current for electrode welding 10-250 A
Welding current for TIG welding 10-300 A
Max current consumption 17 A
Load capacity 60%- 300 A MIG and 60%- 250 A MMA
Arc voltage for MIG welding 16,5- 29 V
Wire feed speed 2- 18 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,85
Efficiency 85%
Protection class IP21S
Insulation class F
Dimensions 920x470x740 mm
Weight 38 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 360 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
With a color LCD screen
Welding current in continuous operation mode at 60% load capacity: max. 250 A for wire welding and 220 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with CO2 gas, steel with mixed gas, welding with filler wire. When a program is selected, the LED next to the corresponding program flashes
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
The large LCD screen allows you to monitor the exact parameters for example.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-250A
Welding current for electrode welding 10-220 A
Welding current for TIG welding 10-250 A
Max current consumption 12 A
Load capacity 60%- 250-A MIG and 60%- 220 A MMA
Arc voltage for MIG welding 16,5- 26,5 V
Wire feed speed 2- 18 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,85
Efficiency 85%
Protection class IP21S
Insulation class F
Dimensions 920x470x740 mm
Weight 39 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 240 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type wire welding device for both wire welding and electrode welding, as well as TIG welding (LIFT lifting ignition)
With single-phase power
Welding current max. 200 A for wire welding, 160 A for electrode welding and 160 A for TIG welding
The device is equipped with simple synergic control for MIG/MAG welding, allowing to set parameters manually.
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance,
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Digital display screens allow for accurate parameter monitoring.
Wire feed mechanism with two drive rollers.
Technical specifications
Wire roll 200mm to 5kg
Power supply 1f 230V +-10%
Welding current for MIG welding 20-200A
Welding current for electrode welding 20-160 A
Welding current for TIG welding 20-160 A
Current consumption max MIG 26,4 A, MMA 23,2 A, TIG 14,4 A
Required mains load protection 25 A C-type
Load capacity 60%- 200 A MIG, 60%- 160 A MMA and TIG
Arc voltage for MIG welding 16- 24 V
Wire feed speed 3- 18 m/min
Weldable wires 0,6-1,0 mm
Wire feed mechanism with two drive wheels
Power factor 0,93
Efficiency 85%
Protection class IP21S
Insulation class F
Dimensions 400x195x270 mm
Weight 10 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
SPARTUS® EasyMIG 125 is a light, compact wire welding machine based on IGBT transistors, with a single-phase 230V supply. Enables welding with gasless filler wire. Maximum welding current 100 A. Equipped with protection functions with intelligent overvoltage, overcurrent and overheating protections. If any of these problems occur, an alarm light will illuminate on the control panel and the welding current output circuit of the device will be automatically shut down to protect and extend the life of the device. SPARTUS® EasyMIG 125 is suitable for working outdoors and on construction sites thanks to its small dimensions and weight. The wire feed mechanism is equipped with two drive rollers and a 1kg/100mm wire roll holder. The MIG welding torch and ground cable are permanently connected to the machine. Technical data: Power supply ~1× 230V ± 10% 50 / 60 Hz Welding current 40 - 100 A Load capacity 30% 100 A Arc voltage 16.6 V Wire feed mechanism, with 2 drive rollers Wire roll 1 kg / Ø100 mm Wire diameter 0.8 mm Current consumption up to 19.6 A Power factor (cos?) 0.58 Insulation class F Protection class IP21S Weight 5.8 kg Dimensions 410×285×150 mm Complete set: • EasyMIG 125 • MIG torch SPE 150 3m • Earthing cable with terminal -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
With a color LCD screen
Welding current in continuous operation mode at 60% load capacity: max. 350 A for wire welding and 300 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with CO2 gas, steel with mixed gas, welding with filler wire. When a program is selected, the LED next to the corresponding program flashes
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
The large LCD screen allows you to monitor the exact parameters for example.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-350A
Welding current for electrode welding 10-300 A
Welding current for TIG welding 10-350 A
Max current consumption 21 A
Load capacity 60%- 350 A MIG and 60%- 300 A MMA
Arc voltage for MIG welding 9,9- 35 V
Wire feed speed 0,8- 16 m/min
Weldable wires 0,8-1,6 mm
Wire feed mechanism with four drive wheels
Power factor 0,93
Efficiency 80%
Protection class IP21S
Insulation class H
Dimensions 920x480x735 mm
Weight 37 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 360 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Inverter type wire welding device for both wire welding and electrode welding, as well as TIG welding (LIFT lifting ignition)
Based on IGBT transistors. With single-phase power
Welding current max. 200 A for wire welding, 180 A for electrode welding and 200 A for TIG welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with 0,6mm wire, 0,8mm wire, 1,0mm wire and Aluminum with 1,0mm wire.
When welding steel, you can choose shielding gas CO2 or mixed gas, there is also a separate program for welding with filler wire. A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Various parameters can be set easily and quickly on the digital screen. When the programs are in place, the screen will graphically display the shape of the weld suggesting the thickness of the material at the given current.
Wire feed mechanism with two drive rollers.
Technical specifications
Wire roll 200mm to 5kg
Power supply 1f 230V +-10%
Welding current for MIG welding 50-200A
Welding current for electrode welding 10-180 A
Welding current for TIG welding 10-200 A
Max current consumption 40A
Required mains load protection 25 A C-type
Load capacity 60%- 200 A MIG, 60%- 200 A TIG and 60%- 180 A MMA
Arc voltage for MIG welding 12,3- 26 V
Wire feed speed 2- 12,8 m/min
Weldable wires 0,6-1,0 mm
Wire feed mechanism with two drive wheels
Power factor 0,76
Efficiency 85%
Protection class IP21S
Insulation class H
Dimensions 490x230x330 mm
Weight 12 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable.
-
Spartus ProMIG 335 DP- Dual Pulse Synergy is a multifunctional inverter welding device,
with which wire welding, electrode welding and TIG welding can be performed.
MIG/MAG welding modes: synergic with double pulse, synergic with pulse, synergic without pulse, with manual setting. A machine suitable for use in industrial production with a high load capacity, with a load capacity of 300% at the maximum welding current of 60A. With three-phase 400 V power supply. Wire feed mechanism with four drive rollers. A compact device with a built-in liquid cooling system, mounted on a base cart. Modern technological solutions have been used in the design of the device. Materials to be welded in the MIG/MAG mode: steel, stainless steel, acid-resistant steels and aluminum alloys.
Allows you to choose the wire type and diameter Special emphasis has been placed on aluminum welding when creating programs and setting options.
Key Features:
1P Pulse- MIG/MAG welding with a pulse, which greatly simplifies spatter-free welding with a spray arc
2P Pulse (Dual Pulse) - MIG/MAG welding with a double pulse, especially suitable for aluminum welding, allows to achieve an approximate result that can be obtained with TIG welding
2T/4T welding modes
Spot welding with a timer
A simple and easy-to-set control panel enables precise control of all welding parameters.
In the manual mode, it is possible to adjust the arc voltage, the speed of the wire feed and the inductance for wire welding.
In the case of synergic control, the welding parameters are set according to the input data.
In the pulse mode, it is possible to set the pulse delta value, pulse frequency, pulse duration and base current.
The wire feed mechanism is equipped with four drive rollers, so a long welding torch can be used for welding.
A 5m torch is included in the set of the device. Despite the compactness and small dimensions, both 5 kg D200 and 15 kg D300 wire rolls can be used.
TIG welding can be performed with lift ignition and 2T/4T switching, current drop and aftergas duration can be set.
Arc force arc dynamics and Hot start e are helpful for MME welding with a melting electrode. simplified arc ignition.
Technical specifications:
Power supply 3 phases 400 V +-10% 50 Hz
Welding current 10- 300 A
Load capacity 60% 300 A
Welding arc voltage 14,5- 29 V
Wire feed mechanism with 4 drive rollers
Wire feed speed 2- 24 m/min
Wire diameter 0,8-1,2 mm
SPOT welding time timer
Wave control - inductance setting
Welding modes 2T/4T/s4T
Smooth wire acceleration when starting welding
Burn-back at the end of the welding arc
Pre- and post-gas
Spoolgun readiness
Welding current for TIG welding 10-300 A
Ignition of the arc during TIG welding with Lift
TIG current drop at the end of welding 0-10
Welding current when welding coated fusible electrodes 10-300 A
Arc force- adjusting the intensity of the welding arc MMA
Hot start - simplified arc ignition MMA
Current consumption MIG 14,8 A, MMA 16,3 A, TIG 11,5 A
Power factor cos phi 0,9
Insulation class H
Protection class IP21S
Weight 58,5 kg
Dimensions 930x490x930 mm
Complete set:
Welding device Spartus ProMIG 335 DP
Wire feed mechanism with 4 drive wheels
Water cooling system
Coolant Hypercoolant
Truck with 4 wheels
MIG torch Spartus SPP241 5m
Electrode holder with 3 m cable
Earth terminal with 3 m cable
Gas hose between the machine and the cylinder -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
Welding current in continuous operation mode at 60% load capacity: max. 300 A for wire welding and 250 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with CO2 gas, steel with mixed gas, welding with filler wire. When a program is selected, the LED next to the corresponding program flashes
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Digital display screens allow for accurate parameter monitoring.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-300A
Welding current for electrode welding 10-250 A
Welding current for TIG welding 10-300 A
Max current consumption 17 A
Load capacity 60%- 300 A MIG and 60%- 250 A MMA
Arc voltage for MIG welding 16,5- 29 V
Wire feed speed 2- 18 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,85
Efficiency 85%
Protection class IP21S
Insulation class F
Dimensions 920x420x740 mm
Weight 38 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 360 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Multipurpose inverter welding device for wire welding, electrode welding and TIG welding with direct current.
In the case of wire welding, it is also possible to perform welding with gasless filler wire and copper solder.
Designed for production welding in all environmental conditions. Load capacity 60% 250A according to EN 90791-1
The structure of the device is based on a modular system, additional devices can be added/changed/replaced by modules.
Equipped with a new welding crater monitoring system that controls the arc energy.
Synergic control, built-in programs for different materials, shielding gases and wire diameters.
55 factory programs, 10 memory locations for your own programs.
Materials to be welded: steel (SG3), stainless steel (Ss-309, Ss-316), aluminum (Al- 5356, Al- 4043), copper solder (CuSi3), Slag filler with wire (Fc- rutile, Fc- basic, Fc-316 ).
It is possible to set the parameters according to the thickness of the material to be welded (mm) or the wire feed speed (m/min). During welding, both arc voltage (V) and amperage (A) are displayed.
It is possible to monitor the wire consumption and consider the cost of welding.
Technical specifications:
Welding current 20A (15 V) - 320 A (30 V)
Load capacity 40 oC 40% 320 A, 60% 250 A, 100% 200 A
Usable welding wire steel 0,6-0,8-1,0-1,2 mm, stainless steel 0,8-1,0-1,2 mm, aluminum 1,0-1,2 mm
Power supply 400 V 3 phases (360- 440 V)
Power consumption max. 17 kVA
Required protection 16 A
No-load voltage 65 V
Wire feed mechanism with 4 drive rollers
Wire feed motor power 65 W
Wire feed speed max. 18 m/min
Wire spool D300- 15 kg
Cooling - automatic air cooling system, new double tunnel system
Protection class IP23
Dimensions 920x270x860 mm
Weight 54 kg
Standards EN90971-1, EN60974-10
Included
grounding cable 35mm2 3m
Aerofeed 5 wire feed mechanism
Intermediate cable 1,7m between machine and feed mechanism 50mm2
Welding torch SX-25, 4m -
Microprocessor controlled wire welding device. Automatic burn-back and soft-start. 10 power levels. Wire feed mechanism with four drive wheels. Adjustable welding time timer 0-2 s. Technical data Power supply 3 phases 400 V Protection 20 A Power consumption 14 kVA/ 11,2 kW Welding current 25- 300 A Load capacity according to EN60974-1 40 oC 300 A 40%, 270 A 60%, 220 A 100% Welding arc voltage 17- 40 V Protection class IP23 Wire roll max. diameter 300 mm Wire roll weight 15 kg Weight 77 kg Dimensions 990x380x790 mm Complete set Earth terminal with 2m cable We complete the device according to the user's needs. -
Spartus ProMIG 500 Dual Pulse Synergy is a multifunctional inverter welding device,
with which wire welding, electrode welding and TIG welding can be performed.
Modern technological solutions are used in the design of the device, such as:
IGBT transistors, PWM (pulse with modulation), MCU (multipoint control unit).
With three-phase power and allows welding in continuous mode with a welding current of up to 500 A.
Materials to be welded in the MIG/MAG mode: steel, stainless steel, acid-resistant steels and aluminum alloys.
Special emphasis has been placed on aluminum welding when creating programs and setting options.
Key Features:
1P Pulse- MIG/MAG welding with a pulse, which greatly simplifies spatter-free welding with a spray arc
2P Pulse (Dual Pulse) - MIG/MAG welding with a double pulse, especially suitable for aluminum welding, allows to achieve an approximate result that can be obtained with TIG welding
2T/4T welding modes
Spot welding with a timer
A simple and easy-to-set control panel enables precise control of all welding parameters.
In the manual mode, it is possible to adjust the arc voltage, the speed of the wire feed and the inductance for wire welding.
In the case of synergic control, the welding parameters are set according to the input data.
The wire feed mechanism is equipped with four drive rollers, so a long welding torch can be used for welding.
A 5m torch is included in the set of the device. Despite the compactness and small dimensions, both 5 kg D200 and 15 kg D300 wire rolls can be used.
Technical specifications:
Power supply 3 phases 400 V +-10% 50 Hz
Welding current 15- 500 A
Load capacity 60% 500 A, 100% 400 A
Welding arc voltage 14,8- 39 V
Wire feed mechanism with 4 drive rollers
Wire feed speed 1,5- 24 m/min
Wire diameter 0,8-1,6 mm
Built-in welding programs- 1P pulse- 23pcs, 2P dual pulse- 23pcs, Synergy- 20pcs
dPC pulsation delta 30- 70 %
FdP Pulse frequency 2P 0,5- 3,0 Hz
dut double pulse width 10- 90 %
bAL welding arc height -10- +10
SPOT welding time timer
Wave control - inductance setting
Welding modes 2T/4T/s4T
SCP initial current 1- 200 %
SAL Initial current welding arc length -10- +10
ECP final current 1- 200 %
EAL final current welding arc length -10- +10
Smooth wire acceleration when starting welding
Burn-back at the end of the welding arc
Pre- and post-gas
Spoolgun readiness
Welding current for TIG welding 10-500 A
Ignition of the arc during TIG welding with Lift
TIG current drop at the end of welding 0-10
Welding current when welding coated fusible electrodes 10-500 A
Arc force- adjusting the intensity of the welding arc MMA
Hot start - simplified arc ignition MMA
VRD- low open-circuit voltage when the device is in standby mode
Current consumption MIG 45 A, MAG 47 A, TIG 37 A
Power factor cos phi 0,7
Efficiency 85 %
Insulation class H
Protection class IP23
Weight 102 kg
Dimensions 1100x500x1500 mm
Complete set:
Welding device Spartus ProMIG 500 Dual Pulse Synergy
Wire feed mechanism with 4 drive wheels
Water cooling system
Truck with 4 wheels
Intermediate cable between the power part of the machine and the wire feed mechanism, 5m
MIG torch Spartus SPP501LCD 5m
Electrode holder with 3 m cable
Earth terminal with 3 m cable
-
Inverter type wire welding device for both wire welding and electrode welding, as well as TIG welding (LIFT lifting ignition)
Based on IGBT transistors. With single-phase power
Welding current max. 220 A for wire welding, 200 A for electrode welding and 220 A for TIG welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available programs: Steel with 0,6mm wire, 0,8mm wire, 1,0mm wire and Aluminum with 1,0mm wire.
When welding steel, you can choose shielding gas CO2 or mixed gas, there is also a separate program for welding with filler wire. A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
Various parameters can be set easily and quickly on the digital screen. When the programs are in place, the screen will graphically display the shape of the weld suggesting the thickness of the material at the given current.
Wire feed mechanism with two drive rollers.
Technical specifications
Wire roll 200mm 5kg or 300mm 15kg
Power supply 1f 230V +-10%
Welding current for MIG welding 50-220A
Welding current for electrode welding 10-200 A
Welding current for TIG welding 10-220 A
Current consumption max. MIG 37A, TIG 28A, MMA 39A
Required mains load protection 25 A C-type
Load capacity 60%- 220 A MIG, 60%- 220 A TIG and 60% 200A MMA
Arc voltage for MIG welding 16,5- 25 V
Wire feed speed 2- 12,5 m/min
Weldable wires 0,6-1,0 mm
Wire feed mechanism with two drive rollers
Power factor 0,76
Efficiency 85%
Protection class IP21S
Insulation class H
Dimensions 570x265x460 mm
Weight 19 kg
Included
Earth terminal with cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with cable.
MIG torch consumables box -
Description
Modern multifunctional two-in-one industrial professional welding device.
Allows welding with MIG/MAG and MMA methods.
The device is manufactured using inverter technology and the highest quality components are used.
The welding current used in MIG/MAG welding max. 420 A and also up to 420 A for electrode welding.
With three-phase 400 V power supply.
With a separate wire feed mechanism, the top-class 4-drive roller wire feed mechanism ensures stable and uniform wire movement even with a long torch, regardless of the type of wire.
The wire feed mechanism is equipped with a comfortable handle and base wheels to move it away from the machine if necessary.
Intuitive control panel allows smooth and precise parameter adjustment: arc voltage, wire feed speed, inductance control
(for MIG/MAG) and welding current (for MMA electrode welding).
At the bottom of the machine, there is a separate openable storage compartment for storing the welding torch, accessories or other necessary items.
The device is equipped with digital displays, and the values of the parameters to be set are displayed on the screens.
Spartus Pro MIG series machines are designed for use in industry and are able to successfully withstand heavy loads under the most difficult working conditions.
Excellent output parameters, load capacity indicators, effective cooling system, durable housing, 2T/4T modes
Technical specifications:
Power supply 3 phases 400 V +-10% 50/60 Hz
Welding current MIG 80- 420 A
Load capacity 60% 420 A
Arc voltage MIG 18-35 V
Wire feed speed 2,5- 21,0 m/min
Wire feed mechanism with 4 drive rollers
Wire spool 200/ 300 mm, 15 kg
Wire diameters 0,8-1,6 mm
2T/4T control
Inductance control
Welding current for MMA electrode welding 30-420 A
Load capacity MMA 60% 420 A
Max current consumption 30,7 A
Power factor cos 0,85
Efficiency 85%
Insulation class F
Protection class IP23
Weight 99 kg
Dimensions 1060x420x1400 mm
Completeness
3m electrode holder
3m grounding cable
Package of intermediate cables between the machine and the wire feed mechanism, 5m
Gas hose with clamps
Gas reducer with two manometers
MIG torch Spartus Pro 360 5m
Wire rollers for 1,0-1,2 mm wire -
Included in the set - Wire welding SOLMIG180 for welding with conventional wire. Wire roll 300mm up to 15kg Technical data Power supply 1f 230V +-20% Welding current 30-180A Power consumption 6,7 kVA Power consumption max 22A Load capacity 20%- 180A Load capacity 60%- 85A Load capacity 100%- 60A Wires to be welded 0,6-1,0, 21mm Protection class IP678S Dimensions 330x600x48mm Weight 500kg Set without manometer Reducer Earthing cable Welding torch - Self-darkening welding mask Optimatic55 Dimensions of visible area 98x16 mm UV/IR protection up to 4 DIN Darkness in light state 9 DIN Adjustable darkness 13- 0,00005 DIN Reaction speed 4 s short time from dark to light - medium-fast Sensitivity can be smoothly adjusted from the outside 5 infrared sensors Power supply solar battery + lithium battery Power on/off switch fully automatic Functions welding-grinding Working temperature -55 oC - + 20 oC Storage temperature -70 oC - +470 oC Mask body material strong impact-resistant polyamide Total weight 0,8 g Made in Spain. - Inefil 15mm/510kg Copper-coated ordinary wire intended for welding carbon-manganese steels belonging to Fe 2-Fe 360-Fe 430 (steel group 510 EN 1/288) with a tensile strength of up to 3 Nmm2. Suitable for welding cisterns, boilers, steel constructions, earthworks and construction systems. Used with Ar+CO2 or CO21 shielding gas (M 439-EN XNUMX). -
Inverter type wire welding device for both wire welding and electrode welding.
With three-phase power
Welding current in continuous operation mode at 60% load capacity: max. 300 A for wire welding and 250 A for electrode welding
The device is equipped with synergic control for MIG/MAG welding, allowing to set parameters manually.
Available synergistic programs for steel 0,8/1,0/1,2 mm wires.
A simple control panel allows you to adjust the following MIG/MAG parameters:
welding arc voltage, wire feed speed, 2T/4T mode, inductance, Arc Force (easier electrode melting in electrode welding), Hot Start (better electrode ignition) and VRD-reduced no-load voltage
Possibility to change the polarity - can also be used when welding with gasless filler wire.
The large digital screen allows you to monitor the exact parameters for example.
Wire feed mechanism with four drive rollers.
Technical specifications
Wire roll 300mm to 15kg
Power supply 3f 400V +-10%
Welding current for MIG welding 50-300A
Welding current for electrode welding 10-250 A
Welding current for TIG welding 10-300 A
Current consumption max MIG 17 A; TIG 14 A; MMA 13 A
Load capacity 60%- 300 A MIG and TIG; 60%- 250 A MMA
Arc voltage for MIG welding 16,5- 29 V
Wire feed speed 2- 12,5 m/min
Weldable wires 0,8-1,2 mm
Wire feed mechanism with four drive wheels
Power factor 0,93
Efficiency 85%
Protection class IP21S
Insulation class H
Dimensions 570x265x460 mm
Weight 19 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 360 3m
Gas hose with hose clamps
Drive rollers for 0,8-1,0 mm wire.
Electrode holder with 3m cable. -
Wire welding for welding with conventional wire. Wire roll 300mm up to 15kg Technical data Power supply 1f 230V +-20% Welding current 30-180A Power consumption 6,7 kVA Power consumption max 22A Load capacity 20%- 180A Load capacity 60%- 85A Load capacity 100%- 60A Wires to be welded 0,6-1,0, 21mm Protection class IP678S Dimensions 330x600x48mm Weight XNUMXkg Set without pressure gauge Reducer Earthing cable Welding torch -
Inverter type modern wire welding device, designed for professional use on a daily basis.
Allows you to weld with conventional wire in both MIG and MAG mode, as well as with gasless filler wire, as it allows you to change the polarity of the welding current.
You can also weld with fusible electrodes (MMA) and TIG lift method. The built-in gas valve and control plug allow the use of a push-button torch for TIG welding.
In addition to IGBT power transistors, MCU controller, PWM technology and PFC filters are used in the internal construction of the device, which together ensure a stable and high-quality welding current.
The device is equipped with the following welding support functions:
Synergic control - 16 built-in welding programs
Wave control - precise adjustment of the dynamics of the welding arc ensures complete control of the welding arc, allows to reduce welding spatter and can adjust the width and penetration of the arc.
Burn back - accurate welding wire speed control reduces the risk of the wire sticking to the wire nozzle, is helpful in finishing welding.
Slow feed- a smooth increase in the speed of the wire at the start of welding. Especially recommended for welding with higher welding currents and/or wire feed speeds.
A smooth wire feed at the start of welding reduces the risk of defects at the start of welding.
2T/4T- 2-stroke and 4-stroke mode
Spool Gun- readiness for welding with a Spool Gun torch. Available as a separate accessory.
Regimes supporting TIG welding: 2T/4T, welding current drop adjustment 0-10s, tail gas adjustment
Modes supporting MMA electrode welding: Hot Start, Arc Force, VRD - low idle voltage in standby mode
The device has been specially designed following the advice and wishes of shipbuilding welders and has been enlarged
resistance to moisture, salty environment and corrosion - so it is well suited for use in metal industries, where there are often difficult environmental conditions.
It is also suitable for those performing repair and maintenance work when working in an outdoor environment.
The maximum welding current in MIG/MAG, MMA and TIG modes is up to 200A.
Wire roll 200mm to 5kg
Wire feed mechanism with two drive rollers
The device is equipped with a large graphic display for monitoring and setting parameters
Technical specifications
Power supply 1f 230V +-10%
Welding current for MIG welding 25-200 A
Welding current for TIG welding 10-200 A
Welding current for electrode welding 10-200 A
Max current consumption 32 A
Load capacity 40% 200 A
Arc voltage for MIG welding 15,3- 24 V
Wire feed speed 2,5- 16,5 m/min
Weldable wires 0,6-1,0 mm
VRD idle voltage 14 V
Power factor 0,99
Efficiency 85%
Insulation class H
Protection class IP23
Dimensions 530x215x410 mm
Weight 17 kg
Included
Ground terminal with 3m cable
Welding torch Spartus Easy 150 3m
Gas hose with clamps
Introductory video:
https://www.youtube.com/watch?v=oUc8iX-FqCA -
Description The device can weld carbon steel, stainless steel, various aluminum alloys, etc. Welding current max. 200A, smooth adjustment without steps. Both remote control and pedal control are available as accessories. When connecting a remote control or pedal, the device automatically recognizes the equipment being used and automatically switches to control from the remote control. The device is suitable for all TIG welding applications with full parameter settings. It is also suitable for welding all electrodes used in electrode welding. Suitable applications for welding tanks, pipelines, boilers, industrial applications and maintenance work. Main features: Arc stability and arc control, in electrode welding, automatic sensitivity adjustment when the distance between the material and the electrode tip changes. Automatic synergistic control for AC parameters (balance-frequency-compensation), simplified, optimal and easy setting. Simple setting and saving of parameters with one button. Double automatic cooling, the fan is activated only when necessary. The tunnel-type cooling system ensures the protection of electronic components from particles coming with the air flow. Air currents move inside the machine only to the components that need cooling. STAND-BY function, the device switches to standby mode if not used for 10 minutes. This ensures a longer life of the electronic components of the device and increases the efficiency of the device. Minimal electricity consumption thanks to excellent energy efficiency. The electronics of the device are built in such a way that the energy from the power supply is used as efficiently as possible. Anti-stick protection, arc dynamics, simplified arc ignition, LIFT lifting and HF non-contact ignition for TIG welding. Built-in supply voltage stabilizer, the device can also be used with generator power and with large supply voltage fluctuations. The device is equipped with VRD voltage reduction device function e. When idling, the voltage drops to a very low level, ensuring safety even when working in very extreme conditions (damp, wet). Technical data Power supply 1 phase 230 V Protection 25 A Power consumption 9,5 kVA Permitted supply voltage 180- 280 V Welding current 10- 200 A Load capacity for electrode welding according to EN60974-1 40 oC 160 A 60%, 130 A 100% Load capacity for TIG welding according to EN60974- 1 40 oC 170 A 60%, 140 A 100% Pulse frequency up to 500 Hz No-load voltage 65 V Protection class IP23 Weight 14 kg Dimensions 465x280x360 mm Complete set Earth terminal with 2m cable TIG torch 4m gas hose -
A welding device with synergic control that can perform the following welding methods: MIG/MAG wire welding MMA welding with a melting electrode TIG welding with direct current (both with and without pulse) TIG welding with alternating current (both with and without pulse) Arc ignition during TIG welding without contact (HF) The device is equipped with two gas valves , you can connect 2 different shielding gases. The device selects and controls which gas valve to control according to the selected welding program. The welding parameters can be selected according to the thickness of the material to be welded and automatically adapt to the corresponding parameters. Up to 10 programs can be stored. Pre-recorded programs with carbon steel (SG3), stainless steel (Ss-309, Ss-316), aluminum (AL-5356, AL-4043), copper-silicon alloys (CuSi3) and filler wires (Fc-Rutile, Fc-Basic, Fc- 316) for welding. Technical data: Max welding current 200 A Load capacity according to standard 40 oC 180 A 60%, 160 A 100% Welding current adjustment range 10- 200 A Arc voltage adjustment range for wire welding 14,5- 25 V Wire coil D300 mm, 15 kg Electrodes used 1,6- 4,0, 1,0 mm Usable electrodes for TIG welding 2,4- 0,6 mm Usable wire diameters 1,2- 2 mm Wire feed mechanism with 1 drive rollers Power supply 230 phase 25 V Required protection 9 A Power consumption 48 kVA No-load voltage 328 V Dimensions 270x453x23 mm Protection class IP60974S Standards EN1-60974, EN10-29,8 Weight 3 kg Complete set Earthing cable 25 m MIG torch SX4 3 m Electrode holder with 17 m cable TIG torch SR3 XNUMX m -
Four in one inverter welding machine. SPARTUS® Multi Pro 200 4in1 is a professional modern inverter welding device based on high-level PWM technology and professional class IGBT transistors. Enables MIG / TIG AC / TIG DC and MMA fusible electrode welding with a current of up to 200A. With single-phase 230V power supply. The device offers many possibilities in the implementation of the previously mentioned welding methods. MIG welding MultiPro 200 4in1 ion equipped with a synergistic system for MIG / MAG welding. It is possible to choose between the following programs: steel, stainless steel, aluminum, welding with gasless filler wire and CuSi brazing. The device also works in manual mode. You can also manually adjust the parameters according to the specified material thickness and wire feed speed. In addition, the device has several supporting functions for MIG welding: – 2T/4T switching – Backburn time – Smooth start – Pre-gas and post-gas – Inductance adjustment The high-class wire feed mechanism with two drive wheels ensures stable wire feed. An important advantage is also the readiness to use the Spool Gun torch. TIG welding Multi Pro 200 4in1 enables advanced level TIG AC and TIG DC welding with arc ignition both contactless with high frequency ignition (HF) and with lift (Lift) method. The device is equipped with an impulse mode, which allows for perfect welding, even with, for example, very thin aluminum material. Multi Pro 200 4in1 TIG welding supporting functions: – AC waveform selection: trapezoidal, sine, triangular – 2T/4T switching – AC balance, AC frequency, pulse frequency, pulse width and pulse amplitude setting – rise and fall setting – SPOT scoring mode MMA welding MultiPro 200 4in1 allows you to weld with the electrode both alternating current MMA AC and direct current MMA DC. Functions supporting electrode welding: - Arc Force - automatic monitoring and correction of the welding arc - Hot Start - simplified arc ignition Modern design, LCD control panel, wireless control with high-level components make SPARTUS® Multi Pro 200 4in1 an outstanding model on the welding market. The SPARTUS® Pro class device is ideal for manufacturing companies and metal industries. Stable wire feed and output parameters guarantee high welding quality. Technical data: Power supply ~1× 230V ± 10% 50 / 60 Hz Welding current MIG [A] 30 - 200 Corrosivity MIG [%] 40 @ 200A Wire feed mechanism with 2 drive rollers Wire spool [kg]/[mm] 5 / 200 Wire diameter [mm ] 0.6, 0.8, 1.0 Add options spool gun, pulse, remote control, Arc Force, Hot Start, wire test, Burn Back, synergy, synergistic programs, brazing (CuSi3), smooth start, MMA electrode welding 2T/4T switching Welding current TIG [ A] 10 - 200 Welding current MMA [A] 10 - 200 Start, end currents YES Pregas [s] 0.1 - 2 Current increase [s] 0 - 10 Current decrease [s] 0 - 10 Aftergas [s] 0 - 10 Current consumption [A] MIG 28.1 / TIG AC 22.2 / TIG DC 22.1 / MMA AC 27.7 / MMA AC 30.5 AC waveforms trapezoidal, sine, triangular TIG arc ignition Lift /HF Power factor (cos?) 0,99 Efficiency ? -
Suitable for models ProTIG 320P and 400P AC/DC Enables setting all welding parameters remotely.
Working radius up to 100 m